Remove the power cord from your PC.
Press and hold the power button on the case of your PC for 30 seconds.
Wait 30 minutes
Reconnect the power cable and start your PC, is there an image on the screen and if so, are you able to boot into BIOS?
Windows 10 installation failing on Triumph Board
![](data:image/svg+xml, %3Csvg xmlns='http://www.w3.org/2000/svg' height='64' class='font-weight-bold' style='font: 600 30.11764705882353px "SegoeUI", Arial' width='64'%3E%3Ccircle fill='hsl(150.4, 75%, 24%)' cx='32' cy='32' r='32' /%3E%3Ctext x='50%25' y='55%25' dominant-baseline='middle' text-anchor='middle' fill='%23FFF' %3EFB%3C/text%3E%3C/svg%3E)
Felix Blakatu
0
Reputation points
I was installing Windows 10 on my triumph board pc. I progressed to the delete partition stage and after deleting the partition, installing the new windows failed with the message "Recreate the drive in Rufus and use partition scheme MBR. So i did just that and now the system doesn't display any signal for me to proceed with the installation. Only blank screen with "No Signal" displaying, meanwhile the keyboard and mouse light indicators show the system is on. How do i resolve this issue to continue with the installation process?
Windows for home | Windows 10 | Install and upgrade
-
![](data:image/svg+xml, %3Csvg xmlns='http://www.w3.org/2000/svg' height='64' class='font-weight-bold' style='font: 600 30.11764705882353px "SegoeUI", Arial' width='64'%3E%3Ccircle fill='hsl(6.4, 45%, 10%)' cx='32' cy='32' r='32' /%3E%3Ctext x='50%25' y='55%25' dominant-baseline='middle' text-anchor='middle' fill='%23FFF' %3EFU%3C/text%3E%3C/svg%3E)
Farhan UL Huq 0 Reputation points2026-05-06T07:48:31.0733333+00:00 - The “No Signal” screen means the PC is ON but not booting correctly to display output, usually due to BIOS/boot mismatch or display output change.
- Try all video outputs on the Triumph Board PC (HDMI / DisplayPort / VGA) and use a different cable or external monitor.
- Force BIOS or Boot Menu access immediately at power‑on using F2, F12, DEL, or ESC (press repeatedly).
- Boot mode and USB type must match – this is the main root cause of the failure.
- If BIOS is set to UEFI, recreate the USB in Rufus as GPT + UEFI (non‑CSM).
- If BIOS is set to Legacy/CSM, recreate the USB as MBR + BIOS (or UEFI‑CSM).
- Do not mix UEFI with MBR or Legacy with GPT – that results in blank screen / no installer.
- Use a rear USB port directly on the device and a different USB stick if possible.
- If BIOS still does not display, perform a full power drain reset or CMOS reset to restore default video/boot output.
- Once installer loads again, select unallocated space and click Next—let Windows create partitions automatically.
Sign in to comment
1 answer
Sort by: Most helpful
-
DaveM121 872.9K Reputation points Independent Advisor2026-05-06T08:10:06.8333333+00:00 -
DaveM121 872.9K Reputation points Independent Advisor
2026-05-06T08:09:31.48+00:00 Remove the power cord from your PC.
Press and hold the power button on the case of your PC for 30 seconds.
Wait 30 minutes
Reconnect the power cable and start your PC, is there an image on the screen and if so, are you able to boot into BIOS?
Sign in to comment -